SCM DMC SD 60 RRCS 135 VN 53" Automatic Wide Belt Sander with Steel & Rubber Drum Combi Head & Electronic Pad

Machine Standard Features

• Grooved rubber coated pressing rollers before and after 2nd and 3rd working unit

• Pneumatic floating pressure shoes  in first working position

• 3HP variable speed feed motor 3.5-18 m/min (12-60 FPM)

• Y-Delta two-stage reduced voltage starter on main motor

• Automatic Electronic Table Positioning Device

• In-feed / Out-feed extended tables for easier part feeding

• Adjustable sanding drum and pad position for micro precision adjustment and pneumatic On/Off

• Electronic digital thickness readout of work table position

• Powered table lifting by means of four heavy duty motor and lifting columns double fastened at both top and bottom of the lifting columns to provide exceptional table stability 

•  Electronic tracking of abrasive belt 

• Pneumatic belt tensioning with center fulcrum to compensate for tapering of abrasive belt 

• Front and rear emergency stop buttons

• Automatic emergency stop of machine for:

            - sanding belt breaking, tensioning, over tracking

• opening of the access door to the operating groups 

          - absence of compressed air

          - overload on main motors

• Amperage meter for main motors allows maximum utilization of available horsepower

• Main disconnect switch with the ability to be locked out by padlock

• In feed flexible steel hold down, and anti-kickback plate

•  50 shore, negative profile (waffle style) rubber feed mat

LOGIC TS CONTROLLER 

FEATURES:

• PLC terminal with LCD color display

• Touch Screen Functions

• Dustproof membrane keyboard

• Graphic representation of the machine configuration

• 120 Working Programs

• Total control of electronic sectional pad (if equipped with electronic sectional pad)

• Control of working thickness.

• Control of feed speed.

• Timing of abrasive belt cleaners. (if equipped with blowers)

• On/Off positioning or timed intervention of all working units.

• Automatic sequential start-up of all the main motors.

• Self-diagnostic of all electrical cards and machine trouble-shooting.

• Ability to name programs and add program notes.

• Machine report (working and stand by hours)

WORKING UNIT SPECIFICATIONS:

1st Working Unit

Working Unit Type: Roller

Motor HP: 30 HP

Motor Type: Single Speed

Abrasive Belt Speed: 18 mps

Drum Size: 140 mm

Drum Type: Steel

Abrasive Belt Length: 85"

2nd Working Unit

Working Unit Type: Roller

Motor HP: 24 HP

Motor Type: Single Speed

Abrasive Belt Speed: 18 mps

Drum Size: 175 mm

Drum Type: 65 Sh Rubber

Abrasive Belt Length: 85"

3rd Working Unit

Working Unit Type: Combination Head with Electronic Sectional Pad

Motor HP: 18 HP

Motor Type: INVERTER

Abrasive Belt Speed: 9 to 18 mps

Drum Size: 160 mm

Drum Type: 45 Sh Rubber

Platen Size: 60 mm

Platens Included: Two

Abrasive Belt Length: 85"

Electronic Sectional Pad:

Machine is equipped with a TSE24 Electronic Sectional Pad.

Complete with 24 section reader bar and 24 individual sections at 55mm distance.  Each section is activated by reader bar to move in or out of position during the sanding of veneer panels.  From the controller you can activate certain sections on the side edges of the panel to move in or out of position to prevent roller over on edges or to increase sanding capabilities of solid wood banded edges.  Also Anti-Dubbing is standard with this style of pad.

TECHNICAL SPECIFICATIONS

Working Width: 1350 mm

Number of Heads Available: Three

Feed Motor: 3 HP

Maximum Work Piece Thickness: 170 mm

Minimum Work Piece Length: 12.5"

Abrasive Belt Size: 53" X 85"

Compressed Air Requirements: 6 Bar (88 PSI)

Dust Outlets: 3 outlets @ 195 mm

Exhaust Requirements: 3750 CFM

Poewer Requirements: 60 V/ Three Phase