Full-Height Cabinet Panels With Real Oak Grain, Ready to Install
The SALT Pura Vita PVRF04 Rovere Firenze is a prefinished real wood veneer panel that arrives finished and ready to cut. At 49 inches wide by 120 inches long in a 19 mm thickness, it covers full-height cabinet sides, tall wardrobe carcasses, and architectural wall panels without a seam. The A-grade front face carries genuine oak grain in a Natural Firenze Oak finish; the B-grade back is real wood to a looser appearance standard, held in reserve for surfaces that will rarely or never be seen.
Key Features
- 13-hour water-resistant core — a vendor test result, not a wet-area rating, and useful where spills and humidity are routine.
- Protective peel coat — transparent over the A face, blue transparent over the B face, so the two are told apart before it comes off.
- Random or plank match — the veneer layup technique, which decides how the grain repeats across the sheet.
- A/B grade real wood veneer faces: the A-grade front is selected for a consistent, show-quality oak appearance, while the B-grade back is the same species to a relaxed standard.
- Natural Firenze Oak finish: an approved web finish name from SALT International for color code PVRF04, describing a natural-toned rift-influenced oak with warmth and even grain character.
- 49 inch by 120 inch nominal sheet: a format sized for tall cabinet carcasses, pantry sides, and full-height wall panels that a standard 4 by 8 sheet would not cover without a joint.
- 19 mm thickness: matches standard confirmat and minifix hardware spacing and pairs with 23 mm edgebanding for a flush square-edge finish.
- Pura Vita collection: SALT International's prefinished real wood veneer program, described by grade pair rather than sidedness because both faces are real wood.
- Factory-finished face: the decorative surface is applied at the plant, so the panel moves directly from saw to assembly with no field finishing step.
Where This Panel Earns Its Place in the Cut List
The 49 by 120 inch format is the defining reason to reach for this sheet. A standard 49 by 97 inch sheet falls short of a 96 inch interior height once a bottom panel is accounted for; the 120 inch length clears that constraint and leaves a workable offcut for a matching toekick or a horizontal shelf end. That makes this format the practical choice for full-height wardrobe carcasses, tall pantry cabinets, floor-to-ceiling library units, and high-wall cladding runs where a horizontal seam is not acceptable. The 49 inch width also accommodates a wider-than-standard part, such as a 48 inch side panel with enough overhang for trimming, without ripping down from a wider sheet.
Construction and Finish Detail
Pura Vita panels carry real wood veneer on both faces, which is what separates them from TFL or PET foil panels in the SALT International range. The grade pair notation — A/B on this sheet — tells you how each face was selected: the A-grade front meets a tighter appearance standard for grain uniformity and color consistency; the B-grade back is the same oak species to a looser standard, suitable for concealed surfaces. Both faces are real wood, not a printed or filmed substitute. The Natural Firenze Oak finish name is SALT's approved descriptor for color code PVRF04, and it governs the name in all downstream documentation. At 19 mm, the panel is built to accept the same confirmat, minifix, and shelf-pin hardware used in a standard 3/4 inch carcass, keeping the hardware schedule simple on a mixed-panel job.
The Right Fit: Shops and Projects That Specify This Sheet
Cabinet shops building furniture-grade or architectural millwork that must pass close inspection specify Pura Vita when the spec calls for real wood and the budget does not support solid lumber throughout. The A/B grade pair suits any component where one face is always visible and the other is enclosed: a wardrobe side that faces the room, a bookcase back that faces the wall, a tall pantry carcass where the interior is lined separately. Designers who specify a wood interior and need the carcass material to hold up in a showroom or a photographed kitchen will find the A-grade face performs at that level. For projects where both faces are visible, the A/A grade panel in this color is the alternative to evaluate.
What does A/B mean on a Pura Vita panel, and is the B-grade back still real wood?
Yes, both faces are real wood veneer. A/B describes an appearance grade pair: the A-grade front is selected to a tighter standard for grain consistency and color evenness; the B-grade back is the same oak species held to a looser appearance standard. It is not a backer sheet or a printed film. If both faces of your component will be visible, the A/A grade panel in the same color is the right choice.
Does matching edgebanding exist for Rovere Firenze PVRF04?
Yes. The Pura Vita collection includes matching edgebanding for its colors. Confirm the specific width and roll length for PVRF04 with your sales contact to be sure the banding in stock aligns with your edge thickness and run length.
Why is the sheet 49 inches wide rather than the standard 48?
The extra inch is trimming allowance. A 49 inch sheet rips cleanly to a finished 48 inch part without squaring a factory edge that may not be perfectly true. For narrower parts the offcut is usable, and for jobs requiring exactly 48 inches the format eliminates the risk of a short panel.
Can I finish or stain the face after installation?
The Pura Vita face arrives factory-finished. It is not designed to be re-stained or overcoated in the field. The finish is part of the veneer program and is the color you see in the panel. If a site touch-up is needed at a cut edge, use a matching touch-up product suited to prefinished veneer.
A Real Wood Panel That Works at Cabinet-Shop Scale
Pura Vita PVRF04 Rovere Firenze delivers a genuine oak face in a sheet format sized for the tall carcasses that drive the most demanding part of a cabinet build, with the thickness and grade to go straight from the saw to assembly without a finishing step in between.
