Matching ABS Edgebanding For Saviola Rialto Hemlock Panels
This is the factory-matched ABS edgebanding for Saviola Rialto Hemlock (GSDS8), supplied in a 43 mm wide, 54-foot short roll at 1 mm thick with a Flash Finish surface. It closes cut panel edges in the same decor as the face, so the finished component reads as a single continuous surface rather than a faced board with a raw core showing.
Key Features
- Factory color match to GSDS8 Rialto Hemlock — produced by the panel maker to align with the Saviola decorative face, not a close third-party approximation.
- 43 mm width — sized to overhang a standard 19 mm panel on both faces, leaving a clean margin for edge trimming.
- 54-foot short roll — a job-sized quantity suited to a single cabinet run or a focused trim-out without committing to a full 328-foot production roll.
- 1 mm ABS thickness — the standard hand-feed and light-machine banding gauge for vertical surfaces and interior faces.
- Flash Finish surface — matches the specific texture and sheen of the Rialto Hemlock panel face so edge and face align visually under direct light.
- Chlorine-free ABS polymer — clears specifications that exclude PVC edgebanding materials.
Where This Edgebanding Fits the Job
Rialto Hemlock is a wood-look decor, and a wood-look panel with a mismatched edge is immediately obvious — the core color reads as a stripe through every door and shelf edge. This banding eliminates that problem by carrying the exact Rialto Hemlock decor and Flash Finish texture around every cut edge. It is the right choice for cabinet box sides, shelf edges, door perimeters, and any other component cut from Saviola GSDS8 panels where the edge will be seen or touched. The 54-foot roll format makes it practical for a focused single-project order: enough material to band a wardrobe run or a kitchen section without the waste associated with a production-length roll on a small job.
Construction and Finish Details
ABS polymer is extruded without chlorine, which distinguishes it from PVC banding and matters on commercial and institutional projects where PVC is excluded from the finish specification. At 1 mm, the strip applies cleanly on a light-duty automatic edgebander or with a hand iron and a glue pot, and trims flush without chipping the face. The Flash Finish designation refers to the surface emboss and sheen profile the vendor assigns to the Rialto Hemlock decor group — using any other finish variant on a Flash Finish panel face will produce a visible texture break at the edge joint, particularly under raking light.
Who Orders This Roll
Cabinet shops producing a Saviola Rialto Hemlock run keep this roll at the edgebander as the dedicated match for that color. Smaller shops and installers doing site repairs or filling out an order buy the 54-foot format specifically because it covers a defined scope without leftover inventory. Designers and millwork specifiers confirm it when Rialto Hemlock panels are in a specification, ensuring the banding color code is documented alongside the panel code so the shop orders the correct match and not a generic substitute.
Can this 43 mm banding be used on panels thicker or thinner than 19 mm?
Yes. The 43 mm width provides enough overhang for a range of panel thicknesses — wider panels simply leave less overhang after trimming, and thinner panels leave more. The trimming step removes the excess regardless, so the width is permissive rather than limiting. Where a much thinner panel is used, confirm the overhang is sufficient to cover both face surfaces cleanly.
Is a 328-foot production roll available in this color and width?
The 54-foot short roll is the available format for the 43 mm width in Saviola colors. If a full 328-foot production roll is needed, confirm availability with your sales contact before planning the order around that format.
What is the Flash Finish, and does it need to match the panel order?
Flash Finish is the surface texture and sheen classification the vendor assigns to the Rialto Hemlock decor. It is not a separate upgrade — it is part of the color program for GSDS8. When you order Saviola GSDS8 Rialto Hemlock panels, this is the correct banding to pair with them. Ordering a banding in a different finish family on the same decor will result in a visible surface mismatch at the edge.
Will this banding work with a standard hot-melt edgebander?
Yes. At 1 mm and without a pre-applied adhesive, this roll is formatted for a hot-melt glue pot edgebander — the standard setup in most cabinet shops. It also applies with a hand iron and contact adhesive for site repairs or very small runs.
The Right Edge for a Rialto Hemlock Job
A panel run is only as finished as its edges. Ordering the factory-matched banding alongside the panel ensures every surface — face and edge — presents the same Rialto Hemlock decor, and the 54-foot short roll puts exactly the right quantity in the shop for a single focused project.
