Vetta Texture On A Wide Edge
This ABS edgebanding in Saviola's GS40R Fantasia decor is the factory-matched edge solution for Fantasia decorative panels in the Saviola collection. At 65 mm wide, it covers a thicker or built-up panel edge and still leaves enough overhang to trim cleanly on both faces. The 54-foot roll is sized for focused runs where a full production roll would go to waste.
Key Features
- Saviola collection color match: produced in GS40R Fantasia to align with the same decor across panel faces and edges.
- ABS construction: chlorine-free polymer that clears specifications excluding PVC and holds color precisely through the banding profile.
- 65 mm width: the widest standard banding width in the Saviola program, suited to thicker substrates and stacked or built-up panel assemblies.
- 1 mm thickness: compatible with standard edgebander glue systems and profiles cleanly on a flush-trim pass.
- Vetta finish: the surface texture from the Saviola Vetta finish family, keeping the edge consistent with the panel face in both pattern and sheen.
- 54-foot roll: a short-run format that lets a shop cover a single project without committing to a full 328-foot production roll.
Where This Width Earns Its Place
The 65 mm width is not a default choice — it is the right choice when the edge is wider than a standard 19 mm panel can fill. Built-up door constructions, stacked shelving edges, thick countertop substrates, and panels doubled for structural rigidity all present an edge that a 23 mm or 43 mm band will not cover adequately. On those components, the 65 mm band reaches past the substrate and gives the trimmer enough material to work with on both the top and bottom flush-trim passes. In a casework run that mixes panel thicknesses, stocking the 65 mm roll alongside the narrower widths means a single color stays consistent from a standard cabinet side to a built-up base end panel.
ABS, Vetta Texture, And The Color Logic
ABS banding is chlorine-free, which matters when a commercial or residential specification calls out PVC exclusions — a growing requirement in healthcare, education, and green-certified projects. Beyond compliance, ABS holds color and gloss consistency through the extrusion more reliably than PVC on fine decors, which is why Saviola builds the matching banding program in ABS. The Vetta finish texture on this roll matches the emboss and sheen of the Vetta-finish Fantasia panels, so the edge does not read as a different surface when the light rakes across a door or drawer face. At 1 mm, the profile is thick enough to protect a corner from incidental contact but thin enough to disappear into a properly set edgebander.
Who Specifies This Roll
Cabinet shops running Saviola Fantasia panels and working with built-up or thicker-than-standard components will reach for the 65 mm roll. The 54-foot format also suits finishing contractors handling site repairs, millwork shops completing a small custom run, or designers sourcing a sample quantity to prototype a detail before committing to production. For any project where Fantasia panels are already on the cut list, this roll is the correct edge closure — a close third-party color is not a match, and a mismatch at the edge is visible from across the room on a textured decor.
Can I use this 65 mm roll on a standard 19 mm panel?
Yes. The banding trims to any panel thickness — the 65 mm width just means more overhang to remove on the flush-trim pass. It works fine on a 19 mm edge, though the 23 mm roll is more efficient for that substrate.
Is this the same ABS banding as the 328-foot roll of the same color?
Yes. The 54-foot and 328-foot rolls are the same banding material in the same color and thickness — the roll length is the only difference. The 54-foot format exists so smaller shops and short runs do not over-buy.
Does matching HPL exist for this Saviola color?
Saviola matching HPL is available and stocked in two sheet sizes. Matching edgebanding in all three widths — 23 mm, 43 mm, and 65 mm — is also available for this color in the Saviola collection.
What edgebander settings work with 1 mm ABS?
Most standard hot-melt edgebanders handle 1 mm ABS without adjustment. Glue pot temperature and feed rate recommendations follow your machine manufacturer's guidelines for ABS material — the banding itself does not require special tooling.
One Roll, One Color, One Clean Edge
When Fantasia is on the panel face, this roll closes the edge in the same decor and texture — and the 65 mm width handles the built-up and thicker components that narrower banding cannot reach.
