Sand Oak ABS Edgebanding For Saviola Panel Runs
This 23mm ABS edgebanding in the Saviola collection's Pecan Gold color (GSDS6) is the factory-matched edge solution for shops working with Saviola TFL panels in the Sand Oak finish. It ships in a 328-foot production roll sized for volume runs, applying a consistent, color-true edge to every cut without chasing a close-enough third-party match.
Key Features
- Factory color match to GSDS6 Pecan Gold: Produced in the same decor as the Saviola panel so face and edge read as a single surface.
- ABS polymer construction: Chlorine-free banding clears specifications that exclude PVC from commercial and residential interiors.
- 23mm width: Sized to cover a 19mm panel with enough overhang on both faces for a clean flush trim pass.
- 1mm thickness: Consistent caliper for reliable feed through automatic edgebanders and manual application alike.
- 328-foot production roll: Sized for cabinet shop volume rather than single-job quantities, reducing changeovers across a run.
- Sand Oak finish: The current finish plate for Pecan Gold in the Saviola program, warm and consistent across the roll.
Where This Edgebanding Earns Its Place
Matching edgebanding matters most on surfaces that get examined up close: drawer fronts, door edges, open shelving, and visible cabinet ends. When banding color drifts from the panel face, the joint announces itself even under ordinary light. The GSDS6 Pecan Gold banding is produced in the same finish program as the panel, so the edge reads as part of the component rather than a patch applied after the fact. It suits both frameless casework where exposed edges are the rule and face-frame work where end panels show a full edge on the finished wall.
Material and Construction
ABS edgebanding is extruded from acrylonitrile butadiene styrene, a chlorine-free polymer that handles color and gloss matching precisely and stays dimensionally stable through temperature changes in the shop. Where a specification calls out PVC-free materials — increasingly common in healthcare, education, and green-rated commercial work — ABS satisfies the requirement without substitution. At 1mm thick, this banding feeds predictably through production edgebanders and irons down cleanly on manual applications, holding its line on straight runs and mitered returns.
Who Specifies This Roll
Cabinet shops running Saviola Pecan Gold panels for kitchen, bath, closet, or commercial casework are the primary buyer. A 328-foot roll supports a production run without the interruption of swapping out part-used spools mid-job, and the full-roll quantity works out to a better cost per linear foot than short rolls where they exist. Designers and millwork contractors specifying Saviola colors by code can call out GSDS6 edgebanding with confidence that the match is the panel maker's own, not an approximation. For a shop that runs a range of Saviola colors, this roll stores alongside its matching panel and pulls when the color does.
Is this banding pre-glued or does it require a glue pot?
This is unglued banding intended for use with an edgebander or contact adhesive. It is not iron-on. A hot-melt edgebander feeds and bonds it in a single pass; manual application uses a compatible contact or EVA adhesive.
What panel thickness does 23mm banding cover?
A 23mm width is the standard choice for 19mm (3/4-inch) panels. The overhang on each face gives a flush trimmer room to clean up both edges without leaving a gap at the corner.
Does matching HPL exist for Saviola Pecan Gold?
Saviola matching HPL is available in this color and ships in two sheet sizes: 73 inch by 120 inch and 60 inch by 120 inch. The 60-inch sheet is the option for shops whose equipment cannot handle the wider format.
Why does the product reference both Pecan Gold and Sand Oak?
Pecan Gold is the color name tied to code GSDS6 in the Saviola program. Sand Oak is the current finish plate that color ships on. Both names refer to the same product; using the color code on a purchase order ensures you receive the correct match regardless of how the color name is printed in a given document.
The Right Edge Keeps the Job Consistent
A factory-matched ABS edge in the same Saviola finish program closes the gap between the panel and the edge without compromise, so the color holds from face to face across every component in the run.
