Full-Sheet A/A Panel for Tall Casework and Open-Shelf Runs
The Saviola Prague Rift decorative panel brings a controlled, straight-grain wood look to cabinet boxes, open shelving, and room dividers where both faces are visible. At 83-5/16 inch by 110-1/4 inch and 19 mm thick, this A/A grade TFL panel ships finished on both sides so either face can show without a second operation.
Key Features
- 13-hour water-resistant core — a vendor test result, not a wet-area rating, and useful where spills and humidity are routine.
- 100% post-consumer recycled core — the Gruppo Saviola board program is built entirely from reclaimed wood fiber.
- CARB2 compliant — meets the California formaldehyde emission limits that commercial and residential specifications ask for.
- A/A grade, finished both sides: identical decorative faces front and back, so open shelves, cabinet interiors, and dividers all read consistently.
- Prague Rift in the Chandler Finish: a straight, tight grain pattern with a controlled linear character suited to contemporary and transitional casework.
- 19 mm thickness: pairs directly with 23 mm edgebanding for a flush square edge, and accepts confirmat and standard cabinet fasteners without pre-drilling adjustment.
- 83-5/16 inch by 110-1/4 inch nominal sheet: sized to yield full-height parts in a single cut, minimizing cross-grain waste on tall door and side panel runs.
- Thermally fused laminate construction: the decorative face is fused directly to the core under heat and pressure, leaving no glue line to open at the edge.
- Matching ABS edgebanding available: color-matched banding in the Prague Rift decor closes the cut edge so panel and edge read as one surface.
Where This Panel Earns Its Keep
The oversized sheet is the practical argument for this panel. At just over 83 by 110 inches, a single sheet covers a full-height side panel or a run of tall shelves with material left over for a fixed shelf or a toe kick. Shops cutting frameless boxes for floor-to-ceiling closets, wardrobe systems, or commercial display cases find the sheet size reduces both the number of joints and the amount of leftover material compared with a standard 49 by 97 sheet. The A/A construction earns its premium specifically on components that are visible from two directions: open bookcases, kitchen islands, back-to-back retail fixtures, and freestanding dividers where there is no concealed face to hide a backer on.
Construction and Surface Character
Prague Rift is a rift-cut oak interpretation: the grain runs straight and close, without the cathedrals of flat-sawn oak or the silver ray fleck of quarter-sawn. The Chandler Finish is a textured matte emboss that gives the surface a tactile depth consistent with the grain direction. TFL construction fuses the printed decor and resin layer directly to the core, so there is no film edge to lift at a router pass or a saw cut. The result is an edge that machines cleanly and takes edgebanding without the gap a separately bonded film can leave. Core type for the Saviola collection is hardwood particleboard; confirm the specific compliance documentation against your project submittal requirements before specifying.
Right Fit: Shop Size and Application
This sheet size suits shops with a panel saw or a beam saw that can handle a full-width board over 83 inches. A cabinet shop running a volume frameless program will cut this sheet efficiently; a smaller bench shop that rarely runs parts longer than 84 inches will find the standard sheet size a better economic fit. The Prague Rift pattern and Chandler texture work well where the specification calls for a linear wood grain without high gloss, including transitional kitchen cabinetry, office casework, and retail millwork where durability matters as much as appearance.
Frequently Asked Questions
What does A/A grade mean on this panel?
Both faces carry the same decorative finish to the same appearance standard. Either side can face out, which is what separates an A/A panel from an A/B panel with a plain backer. If only one face will ever show, an A/B panel in the same color is the more economical choice.
Is matching edgebanding available for Prague Rift?
Yes. Matching ABS edgebanding is available in the Prague Rift decor. ABS is chlorine-free, so it meets specifications that exclude PVC banding. Confirm the width you need against the 19 mm panel thickness when ordering.
Can this panel be used for a kitchen cabinet interior?
Yes. The A/A construction is more panel than a box interior typically needs, but there is no restriction on using it there. If the interior face is never seen, the same collection's A/B panel, where available, would cover the application at lower cost.
Does this panel come in a smaller sheet size?
The Saviola collection in the Prague Rift color is stocked at this sheet size. Check the sibling listings in the same color for other available sizes and constructions.
Is matching HPL available for this color?
Saviola HPL is available in this program and ships in two sheet sizes: 73 inch by 120 inch and 60 inch by 120 inch. Order the 60 inch sheet if your shop cannot process a 73 inch width. Confirm Prague Rift availability in the HPL program when ordering.
Full-Sheet Efficiency, Finished Both Sides
The Saviola Prague Rift A/A panel gives a shop a large, finished-both-sides board in a straight-grain wood look that works as hard on an open shelf as it does inside a closed cabinet box.
