Edgebanding For Single-Job Coverage in a Matched Decor
This is the 43mm wide, 54-foot roll of SALT Saviola ABS edgebanding in color GSR95 Benevento with a Chandler finish — the short-roll format that lets a shop close out one job in a matched color without committing to a full production roll. At 1 mm thick, it applies cleanly on a standard edgebander and trims flush on 19 mm panels.
Key Features
- Matched to Saviola GSR95 Benevento — color and texture are coordinated with the Saviola decorative panel program in this decor.
- ABS construction — chlorine-free polymer that meets specifications where PVC is restricted.
- 43mm width — sized to overhang a 19 mm panel on both faces for clean flush trimming.
- 54-foot short roll — right-sized for a single cabinet run or a repair job without leftover footage.
- 1 mm thickness — compatible with standard edgebanding machinery and light-duty glue pot setups.
- Chandler finish — surface texture follows the Saviola Chandler finish family for a consistent look at the edge.
Where This Roll Fits in a Project
The 54-foot roll exists for jobs where a 328-foot production roll would simply go to waste. A single vanity, a run of floating shelves, a kitchen island end panel — these are the situations where buying a full roll means storing 270 feet of banding you may never use again. The 43mm width works on any panel at or under 38 mm, and most casework in this color runs at 19 mm, so there is plenty of trim margin on both faces. The Chandler finish texture carries across from the panel face to the edge, so the joint reads as one surface rather than two components meeting at a line.
Material and Construction
ABS is the standard banding polymer for European decorative panel programs, and it earns that position because it is chlorine-free and dimensionally stable enough to hold a precise color and texture match. PVC banding is common and functional for general casework, but where a project specification calls out chlorine-free materials — commercial interiors, healthcare, school furniture — ABS is what the spec requires. The 1 mm thickness is the industry standard for machine application and gives the finished edge enough body to take a light knock without lifting. Texture matching at 1 mm is more consistent than at thinner gauges, which matters when a Chandler-finish panel and its edge band are seen together under raking light.
Who Orders the 54-Foot Roll
Small cabinet shops that run a wide color palette keep short rolls on hand so a single color does not tie up cash in footage that sits on the shelf. Designers and installers sourcing for a one-off renovation or a small commercial refresh use the short roll to match a panel order without over-buying. The 54-foot format is also the practical choice when a production shop needs to complete a partial run after the main roll is gone, or when a repair calls for a few feet of a specific decor. If a large production run in GSR95 Benevento is planned, the 328-foot roll is the better value per foot.
Will this banding match the GSR95 Benevento Saviola panel exactly?
This edgebanding is produced to coordinate with the Saviola panel program in the GSR95 Benevento decor. Color and texture are matched at the collection level, so the edge reads consistently with the panel face under normal lighting conditions. Natural variation between production runs is inherent to any matched program — if color consistency is critical, order banding and panels from the same production lot where possible.
What panel thickness does the 43mm width work with?
A 43mm band gives adequate overhang on panels up to approximately 38 mm thick, and it is the standard width for 19 mm casework panels. The overhang trims flush on both faces with a standard flush-trim unit on most edgebanders.
Is this roll pre-glued or does it require a glue pot?
This roll is not pre-glued and is intended for machine application with a hot-melt adhesive edgebander. It is not an iron-on product.
Is matching HPL available in this color?
Matching high-pressure laminate is available for the Saviola collection. Contact the sales team for sheet size and availability in GSR95 Benevento.
The Right Edge for a Finished Result
A panel that matches at the face and misses at the edge reads as unfinished work. This roll closes that gap for GSR95 Benevento jobs, in a quantity that makes sense for the scale of the project.
