Wire-Brushed Oak Texture, Ready to Run on Every Cut Edge
This ABS edgebanding in color PVQS06 Quercia Spazzolato carries the Natural Rift Cut Light Oak Wire Brush finish from the Pura Vita collection onto every exposed cut edge, closing the core and delivering a coherent surface from face to edge. At 43 mm wide and 1 mm thick, the band is sized for the panel thickness most Pura Vita casework is built on, and the 328-foot roll keeps a full kitchen or closet project running without a mid-job changeover.
Key Features
- PVQS06 Quercia Spazzolato color match — the finish is produced to align with the Pura Vita panel program so face and edge read as one continuous surface.
- Wire-brushed oak character — the rift-cut grain pattern and open-pore texture translate directly onto the banding, so the edge carries the same tactile depth as the panel face.
- 43 mm width — sized to cover the panel edge with enough overhang to trim flush on both faces after application.
- 1 mm ABS construction — chlorine-free polymer that stays dimensionally stable through temperature cycling and clears specifications that exclude PVC.
- 328-foot production roll — enough linear footage to finish a full run of tall doors or a multi-cabinet closet build without splicing rolls.
Where Wire-Brushed Oak Makes the Edge Work Harder
A wire-brushed wood face creates a specific expectation: the grain should be readable by touch, not just by eye. On a wide cabinet door or a long shelf, that texture is part of the design language, and an edge that reads smooth or flat breaks the effect. Matching banding in PVQS06 carries the rift-cut line and the open-pore relief around every exposed edge, so the surface language stays intact whether the piece is viewed face-on or from the side. That consistency matters most on handleless door programs, open shelving, and any component where the edge is seen at close range during use.
ABS Construction and Its Practical Advantages
ABS is the material of choice wherever specifications limit or prohibit PVC, and it is a reliable performer in general casework regardless of whether the spec requires it. The polymer is chlorine-free and holds its dimensions across the temperature range a typical cabinet environment sees, which keeps glue lines tight and reduces lifting at the corners over time. At 1 mm, this band has enough body to resist edge impact without adding a visible step at the joint. The color is consistent roll to roll, which matters on a long run where two rolls may be needed across the same job.
The Right Shop and the Right Job for This Roll
This banding is the correct companion for any project already specified in Pura Vita PVQS06. Cabinet shops running Pura Vita panels for residential kitchens, bath vanities, or fitted closets will find the 328-foot roll well-matched to a full-room scope: enough footage to cover a complete job in one order without a surplus that sits on the shelf. Designers specifying a natural wood look with a contemporary rift-cut grain will find the wire-brushed texture adds authenticity that a printed or foil face cannot replicate. The 43 mm width is the right choice for the panel thickness this collection is built on; the 23 mm width is available for thinner components within the same program.
Does the wire-brushed texture on the banding actually match the feel of the Pura Vita panel face?
The banding is produced in the same PVQS06 decor as the panel, so the rift-cut pattern and the open-pore texture are consistent across both. The feel under the hand will be closely aligned, though the panel face and the banding are different constructions and minor variation is inherent between a full panel and an extruded edge strip.
Can this banding be applied with a standard edge bander, or does the wire-brushed texture require special tooling?
This is a standard 1 mm ABS roll and runs on any edge bander set up for 1 mm banding. No special tooling is needed for the wire-brushed finish. Trimming and scraping settings are the same as for any other 1 mm ABS band.
Is matching HPL available in PVQS06 to carry the color onto a countertop or worksurface?
Matching HPL is not part of the Pura Vita program. The collection's matching components are the edgebanding and the panel itself. For a worksurface in the same color family, a separate HPL program would need to be specified independently.
What is the difference between this 43 mm roll and the 23 mm roll in the same color?
Width is selected by panel thickness. The 43 mm band is sized for the thicker panel construction the Pura Vita program is typically built on, giving enough overhang to clean up both faces after application. The 23 mm band serves thinner components in the same color program.
One Roll, One Color, One Consistent Edge
When the face is Pura Vita PVQS06, the edge should be too — and this roll closes that gap across a full project scope without compromise on texture, color, or material.
