An A/A TFL Panel For Casework That Shows on Every Face
The Saviola Coral Sand panel in the Laguna finish is a thermally fused laminate decorative panel finished on both faces, sized at 83-5/16 inch x 110-1/4 inch and built on an 8 mm core. Because both faces carry the same decor, it works wherever a component is visible from more than one direction — open shelving, room dividers, cabinet backs behind glass doors, and freestanding units that float away from a wall.
Key Features
- 13-hour water-resistant core — a vendor test result, not a wet-area rating, and useful where spills and humidity are routine.
- 100% post-consumer recycled core — the Gruppo Saviola board program is built entirely from reclaimed wood fiber.
- CARB2 compliant — meets the California formaldehyde emission limits that commercial and residential specifications ask for.
- CARB2 hardwood particleboard core — the substrate the decor is fused to.
- A/A grade pair construction means the Coral Sand decor appears on both faces, so either side can face out.
- Laguna finish delivers a consistent surface texture that reads cleanly across a run of panels without visible variation between sheets.
- 83-5/16 inch x 110-1/4 inch sheet size gives 63.79 square feet per sheet, sized to nest tall cabinet parts efficiently without an oversized first cut.
- 8 mm thickness suits lightweight back panels, thin partitions, and interior components where a full 19 mm board would add unnecessary mass.
- Matching ABS edgebanding is available in this color, so cut edges close to the same Coral Sand decor without a visible seam.
- Thermally fused laminate surface bonds the decorative face directly to the core under heat and pressure, leaving no adhesive layer to open at the edge.
Where This Panel Fits the Job
An 8 mm A/A panel earns its place in parts of a project where weight matters and both faces are in view. Interior partitions in a modular shelving system, the back panel of a display cabinet with a glass door, or a desk privacy screen are typical applications. Because the sheet runs over 110 inches in the long dimension, it covers a full-height interior partition in a single piece on most residential and light-commercial casework, eliminating a horizontal joint. Cabinet shops laying out back panels, interior dividers, or small door blanks will find the sheet proportions favorable for minimizing waste on standard-depth boxes.
Surface, Color, and Construction
Coral Sand sits in warm, neutral territory — a sand-toned color that reads well against both natural wood decors and cooler whites without pulling strongly toward either. The Laguna finish gives it a consistent tactile surface. TFL construction fuses the decorative paper into the board face rather than bonding a separate sheet, which means the decor is part of the panel structure and does not peel or lift at cut edges before banding is applied. At 8 mm, this is a lighter-duty board than the 19 mm Saviola panels in the same collection — it is built for interior components, not for structural carcass walls or face frames.
Who Specifies This Format
Cabinet shops running a coordinated color program through an entire project reach for the 8 mm A/A to handle the parts a 19 mm board would overbuild. Designers specifying open millwork — shelving intended to be walked around, peninsula cases, or island backs — use an A/A panel so the installer does not need to track which face points which direction. For a homeowner or contractor doing a single renovation, the large sheet size means fewer seams and a cleaner result on any interior that takes a full-height panel. Matching edgebanding in Coral Sand keeps the color consistent at every exposed edge.
What does the A/A grade pair mean on a Saviola panel?
A/A means the Coral Sand decor is applied to both faces of the sheet at the same appearance standard. Either face can be the show face — there is no backer-only reverse side. This is the distinction that separates the A/A panel from an A/B panel, where one face is finished to a tighter grade and the reverse to a looser one.
Is 8 mm thick enough for a cabinet back panel?
Yes, for most face-frame and frameless box constructions where the back is captured in a dado or rabbeted into the carcass. An 8 mm back adds rigidity to the box without the weight of a thicker board. If the back is expected to carry structural load or to act as a shear element in a tall unit, check your design against the load before specifying a thin panel.
Does matching edgebanding exist for Coral Sand?
Yes. Matching ABS edgebanding is available for the Saviola collection in this color. ABS banding is chlorine-free and holds color consistently, so the edge reads as a continuation of the face rather than a visible strip.
Can I order matching HPL in Coral Sand to carry the color onto a countertop?
Saviola HPL is stocked in 73 inch x 120 inch and 60 inch x 120 inch sheets, and Coral Sand may be available in that program. Check the Saviola HPL listings for GSP42 to confirm current availability in the sheet size your shop can process.
How does the 83-5/16 inch x 110-1/4 inch sheet size affect my cut list?
The long dimension clears 110 inches, which covers a standard 96-inch interior height with room for a rip and a squaring cut. The 83-5/16 inch width yields multiple standard depths across a single rip pass. At 63.79 square feet per sheet, it is a larger-than-4x8 format, so confirm your panel saw or CNC can handle the full dimension before ordering.
The Right Panel, Ready to Cut
Coral Sand in the Laguna finish on a two-faced 8 mm sheet gives a shop or installer a versatile interior panel that works without orientation constraints — land either face outward, cut to the list, band the edges, and move on to the next component.
