Full-Height Cabinet Panels in the Gran Tour Finish, Cut-Ready at 83-5/16 Inches
The Saviola A/A decorative panel in color GSAM1 Vogue brings a refined, consistently textured surface to both faces of every sheet. At 83-5/16 inches by 110-1/4 inches and 19 mm thick, this panel is sized to yield full-height cabinet components with usable offcuts, and the Gran Tour finish delivers a tactile, structured surface that holds up through daily handling in finished casework.
Key Features
- 13-hour water-resistant core — a vendor test result, not a wet-area rating, and useful where spills and humidity are routine.
- 100% post-consumer recycled core — the Gruppo Saviola board program is built entirely from reclaimed wood fiber.
- A/A grade construction means both faces carry the same decorative surface, so either side can face outward without compromise.
- Gran Tour finish gives the panel face a deep, structured texture that adds visual and tactile depth to flat door and box surfaces.
- 19 mm thickness supports standard confirmat fasteners and pairs directly with 23 mm ABS edgebanding for a clean, flush edge.
- 83-5/16 inch by 110-1/4 inch sheet yields 63.79 square feet per panel, sized to nest full-height components efficiently.
- CARB2 compliant hardwood particleboard core provides consistent density for machining, routing, and fastener holding across the full sheet.
- Matching ABS edgebanding is available in this color, so cut edges close cleanly without sourcing a third-party match.
Where This Panel Fits the Work
The A/A construction makes this panel the right choice wherever both faces of a component are visible: open shelf units, room dividers, cabinet ends seen from inside and out, and tall wardrobe carcasses where the interior and exterior read together. The sheet dimensions are particularly well-suited to full-height door blanks and tall back panels — the 110-1/4 inch length accommodates a finished door height that a standard 4 by 8 sheet cannot cover without a joint. Shops running closet systems, display casework, or modular furniture benefit most from a panel that never requires a decision about which face to orient outward.
Surface, Core, and Build
The Vogue color in the Gran Tour finish family sits in the Saviola collection, SALT International's thermally fused laminate program. The decorative face is fused directly to the substrate under heat and pressure — there is no separate adhesive layer and no glue line to open at the edge. The core is CARB2 compliant hardwood particleboard, which machines predictably, holds a confirmat screw without splitting, and stays flat across a wide run of parts. At 19 mm, the panel is the standard cabinet-box thickness that edgebanders and boring machines are already set up for, so there is no tooling adjustment between this sheet and the rest of a typical run.
Who Orders This Panel
Cabinet shops building production runs of open-back shelving or frameless box cabinets are the core buyer — the A/A grade eliminates the sorting step that slows a line when both faces need to show. Designers specifying a textured, structured surface for contemporary residential or light commercial millwork will find the Gran Tour finish family delivers enough tactile relief to read well under raking light without reading as rustic. For fabricators estimating material, the 63.79 square feet per sheet figure makes the per-unit cost calculation straightforward against a cut list.
Does the Gran Tour finish match across different colors in the Saviola collection?
Yes. Gran Tour is a finish family shared by multiple colors in the Saviola line, so the emboss and texture profile are identical across any two colors in that family. A joint between GSAM1 Vogue and another Gran Tour color reads as a deliberate color change, not a surface mismatch.
Is matching edgebanding available for GSAM1 Vogue?
Yes. Matching ABS edgebanding is available for this color in the Saviola collection. ABS is chlorine-free and holds color tightly to the panel face, which matters most on a structured finish where a mis-matched banding texture would stand out.
What does A/A mean on this panel, and how is it different from an A/B panel?
A/A means both faces are finished to the same decorative standard — the show face and the back face are interchangeable. An A/B panel carries the decorative face on one side and a backer on the reverse. Choose A/A when both faces of the component are visible; A/B is the right call when one side is always concealed.
Can this panel be used for cabinet interiors as well as exteriors?
Yes, and the A/A construction is particularly well suited to it. An open cabinet or bookcase where the interior shelves and the exterior box sides are both seen benefits from a panel that presents the same surface on both faces. The Gran Tour texture holds up to light contact and routine cleaning in interior applications.
A Panel Built to Run, Not to Sort
The Saviola A/A panel in GSAM1 Vogue removes a decision point from every component that comes off the saw — with the same finish on both faces and a core sized for standard hardware, the sheet goes from delivery to cut list without qualification.
